An old painted timber verandah bracket lying flat on a bench, with its scroll and stepped edge showing

An old painted verandah bracket. One good one is all we need to cut the copies.

What we cut

Brackets and trim, copied from the old one

  • Verandah brackets and post brackets, copied from an old one or cut to your drawing
  • Corbels, frieze and valance pieces, and gable infill panels
  • Fretwork brackets with the cut-through pattern in
  • A run of identical copies, so every post on the verandah matches
  • Plywood and marine ply to 25mm, MDF to 32mm
  • Pieces up to 2500 x 1500
  • Traced from the old piece, a paper template or a photo if you have no file

We cut the pieces, ready for you or your builder to sand, paint and fit. These are decorative pieces: fixing them to the house, and anything that has to carry a load, is up to you or your builder. Tell us if the piece is going outside so we can talk through the right material.

How a copy is made

From one old bracket to a full set

Old Queenslander brackets were cut by hand, so the pattern changes from house to house and a shop-bought bracket rarely matches. If one is missing, rotted or split, a good one from the same verandah is the pattern for the rest.

  • Pen outline of an old verandah bracket, traced around the bracket onto a sheet of paper

    1. Trace the old bracket

    Lay the old bracket flat on paper and run a pen around it, or bring it in and we do it. A full-size tracing beats a photo, because nothing gets stretched by the camera angle.

  • CAD drawing of the same bracket as one smooth closed outline, with node points along the curves

    2. Redraw it in CAD

    The tracing is scanned and redrawn as one clean outline: the wobbles in the pen line come out, the curves stay. You get the drawing to check before anything is cut.

3. On the machine

Cut the copies, every one the same

Once the outline is drawn, the router follows it exactly. Cut two or twenty and they all match, so the new brackets line up with the old ones along the verandah.

Cutting a curved profile in ply. A bracket is cut the same way, as many times as you need.
Cutting thick stock, the way a chunky bracket or corbel is cut.

Who we cut for

Renovators, builders and home owners

Restoring a Queenslander verandah: bring in a good bracket, corbel or frieze piece from the house and we copy it, so the new ones match the rest.

Builders and carpenters: a set of brackets or gable infill panels cut to the sizes on your plans, as one-offs or a matching run.

No old piece left? A clear photo of a bracket still on the house, taken square on with a measurement across it, is enough to draw from. Or send a sketch and we draw it up in CAD for you to check first.

Thicker than one sheet? Tell us the thickness of the old bracket and we'll talk through how to get there. More on the sheets we cut on the plywood and MDF page.

Recent Work

Off the Multicam

3D model of a square MDF peg board with a grid of 484 holes and a hand slot at each corner

18 November 2026

484-hole peg board in 18mm MDF

MR MDF 18mm Drawn from a sketch

A sketch turned into a 3D model and a dimensioned drawing: 484 holes on a 50 mm grid in an 1190 x 1190 sheet of 18mm moisture-resistant MDF, with four hand slots.

Read →
3D model of a wall sculpture made of 40 plywood ribs forming a rolling wave on a mounting board

16 November 2026

Wave wall sculpture: 40 plywood ribs

Marine ply 15mm 3D design check

A 1.8 m wave wall sculpture built in 3D from a set of drawings: 40 ribs in 15mm ply on a mounting board, plus one change we suggested to make it easier to assemble.

Read →
Batch of bolt template assemblies in 17mm form ply fitted with hold-down bolts, ready for delivery

30 May 2026

Bolt templates in form ply

Film face form ply 17mm Bolt template

Bolt templates cut from 17mm film face form ply for a local steel fabricator — they lock the hold-down bolt pattern in place during the concrete pour for steel columns on construction projects across Townsville and beyond.

Read →

See all recent work →

How it works

Three steps. No fuss.

  1. Send your DXF

    Email your DXF or DWG with material, thickness and quantity.

  2. Quote in 24 hours

    We come back with a quote covering material, cutting and any finishing.

  3. Parts in 3–5 days

    Standard turnaround. Same-day possible for simple high-volume runs.

The machine

Multicam SR2515vi

Australian-built flatbed CNC router. 2500 × 1500 mm bed handles a standard 2440 × 1220 sheet.

Bed
2500 × 1500 mm
Accuracy
±0.1 mm
Hold-down
Vacuum table
Tooling
HSD spindle, ATC

Service area

Townsville workshop. North Queensland & beyond.

We're a workshop in Townsville, by appointment. Collection welcome. Freight available to surrounding areas for larger orders — and we've shipped jobs as far as Brisbane.

  • Townsville
  • Burdekin
  • Charters Towers
  • Hinchinbrook

Questions

Quoting & pricing

Do I need a CAD file to get a quote?
No. A DXF or DWG is great if you've got one — but a photo, a sketch or just your measurements is enough. We'll draw it.
What does a drawing cost?
Simple parts from $29.95 + GST, bigger or multi-part jobs from $75 + GST. Whatever you pay comes off your cut price if you go ahead.
How much does the cutting cost?
Every job is quoted — it depends on the material, thickness, how much cutting and the quantity. Send what you've got and we'll quote within 24 hours.
What can you cut?
Plywood to 25mm, MDF to 32mm, aluminium to 16mm, ACM to 4mm, acrylic and plastics to 20mm, and form ply to 17mm — up to 2500 × 1500.
Who do you work with?
Our Townsville workshop is in Garbutt. Trade, business and DIY jobs all welcome.

Send a photo of the old bracket and we'll quote within 24 hours.