Plywood sheet for a speaker cabinet on the CNC router bed, with round cut-outs and two recessed hatch pockets

What we cut

Enclosure panels, ready to glue up

  • Sub box and subwoofer enclosure panels, sealed or ported, including slot ports
  • Speaker baffles with the driver cut-outs in, round or rebated
  • Bass and guitar speaker cabinet panels
  • MDF to 32mm, plywood and marine ply to 25mm
  • Locating grooves and braces cut in, so the panels line up when you glue them
  • One-off boxes, matched pairs, or repeat runs of the same box for installers
  • Cut from your plans or drawing, or drawn up from a sketch
  • Flat-pack kits from published box plans: we supply the sheet, cut every panel and you glue it up
  • Box carpet cut to match: the same machine cuts the carpet pieces with a drag knife, from the same drawing as the panels

We cut the panels and the carpet, ready for you to glue up, cover and fit out. Drivers, wiring, painting, gluing the carpet on and installation are not part of what we do.

A recent job

Twin bass cabinets in 18mm and 12mm okoume ply

A pair of bass cabinets cut on our Multicam from 18mm and 12mm okoume ply, with the parts for both nested across six sheets. This is what goes into a cabinet job like that.

  • Grooves that line the panels up

    Locating grooves 5.3mm deep are cut into the panels, so each one drops into its spot and the cabinet squares itself up when it is glued.

  • Groove ends cut for square panels

    A router bit is round, so the groove ends are dog-boned. A square-edged panel seats right into the end of the groove with no filing.

  • Machined on both sides

    Where the design has work on both faces, the sheet is flipped on locating pins so side two lines up with side one.

  • Braces and a recessed hatch

    Braces are cut with their cut-outs in, and the hatch is cut with a recessed back, ready to fit.

  • Sub box cabinet panels nested and cut in a sheet of plywood on the CNC router bed

    Nested to save sheet

    Both cabinets laid out together, so the parts came out of six sheets.

  • Plywood sheet on the CNC router after the second side was machined, showing grooves and recessed pockets

    Side two, after the flip

    Grooves and pockets cut on the second face, lined up on locating pins.

On the machine: cutting the nested panels.
Brace cut-outs and recessed openings, done.

From CAD to cut

Drawn in full before a sheet goes on the bed

The whole cabinet is modelled in CAD, every panel, brace and baffle, so we can check it goes together before anything is cut. Every panel is located by grooves, so it goes together in order.

CAD section drawing of the bass cabinet with overall dimensions, the driver baffle and vent panel, next to a 3D cut-away of the model
3D cut-away of the cabinet showing the braces, baffles and internal panels
Cut-away: the braces and baffles inside.
3D model of the finished cabinet, closed, with its recessed handles and top openings
The finished box, closed up.
Assembly order, panel by panel.

Who we cut for

Installers, box builders and musicians

Car audio installers: send the box once and we can cut the same sub box again whenever you need it, or a custom enclosure to fit a ute, 4WD or boot.

DIY builders: building a ported or sealed box from a set of plans? Send the drawings or a DXF and we cut the panels to suit. Only got a sketch with the box sizes, the driver size and where the port goes? We draw it up in CAD and send you the drawing to check before anything is cut.

Flat-pack kits: found a box design you like in a set of published plans? Send us the plans you have bought or are free to use. We supply the sheet, cut every panel and send it out flat-packed, ready for you to glue up.

Carpet to cover it: we cut the box carpet too. The router swaps the spindle for a drag knife and cuts every carpet piece from the same drawing as the panels, so the covering fits the box without trimming around the baffle and port cut-outs. We can supply the carpet, or cut your own (new carpet only).

Musicians: bass and guitar speaker cabinet panels, baffle cut-outs included.

More on the sheet timber we cut on the plywood and MDF page, or see everything the machine does on CNC routing.

Recent Work

Off the Multicam

3D model of a square MDF peg board with a grid of 484 holes and a hand slot at each corner

18 November 2026

484-hole peg board in 18mm MDF

MR MDF 18mm Drawn from a sketch

A sketch turned into a 3D model and a dimensioned drawing: 484 holes on a 50 mm grid in an 1190 x 1190 sheet of 18mm moisture-resistant MDF, with four hand slots.

Read →
3D model of a wall sculpture made of 40 plywood ribs forming a rolling wave on a mounting board

16 November 2026

Wave wall sculpture: 40 plywood ribs

Marine ply 15mm 3D design check

A 1.8 m wave wall sculpture built in 3D from a set of drawings: 40 ribs in 15mm ply on a mounting board, plus one change we suggested to make it easier to assemble.

Read →
Batch of bolt template assemblies in 17mm form ply fitted with hold-down bolts, ready for delivery

30 May 2026

Bolt templates in form ply

Film face form ply 17mm Bolt template

Bolt templates cut from 17mm film face form ply for a local steel fabricator — they lock the hold-down bolt pattern in place during the concrete pour for steel columns on construction projects across Townsville and beyond.

Read →

See all recent work →

How it works

Three steps. No fuss.

  1. Send your DXF

    Email your DXF or DWG with material, thickness and quantity.

  2. Quote in 24 hours

    We come back with a quote covering material, cutting and any finishing.

  3. Parts in 3–5 days

    Standard turnaround. Same-day possible for simple high-volume runs.

The machine

Multicam SR2515vi

Australian-built flatbed CNC router. 2500 × 1500 mm bed handles a standard 2440 × 1220 sheet.

Bed
2500 × 1500 mm
Accuracy
±0.1 mm
Hold-down
Vacuum table
Tooling
HSD spindle, ATC

Service area

Townsville workshop. North Queensland & beyond.

We're a workshop in Townsville, by appointment. Collection welcome. Freight available to surrounding areas for larger orders — and we've shipped jobs as far as Brisbane.

  • Townsville
  • Burdekin
  • Charters Towers
  • Hinchinbrook

Questions

Quoting & pricing

Do I need a CAD file to get a quote?
No. A DXF or DWG is great if you've got one — but a photo, a sketch or just your measurements is enough. We'll draw it.
What does a drawing cost?
Simple parts from $29.95 + GST, bigger or multi-part jobs from $75 + GST. Whatever you pay comes off your cut price if you go ahead.
How much does the cutting cost?
Every job is quoted — it depends on the material, thickness, how much cutting and the quantity. Send what you've got and we'll quote within 24 hours.
What can you cut?
Plywood to 25mm, MDF to 32mm, aluminium to 16mm, ACM to 4mm, acrylic and plastics to 20mm, and form ply to 17mm — up to 2500 × 1500.
Who do you work with?
Our Townsville workshop is in Garbutt. Trade, business and DIY jobs all welcome.

Send your box plans or a sketch and we'll quote within 24 hours.